Auto Page CPX-3600 Dokumentacja Strona 218
- Strona / 243
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Electrical characteristics ST72321xx-Auto
218/243 Doc ID 13829 Rev 1
19.12.2 General PCB design guidelines
To obtain best results, some general design and layout rules should be followed when
designing the application PCB to shield the noise-sensitive, analog physical interface from
noise-generating CMOS logic signals.
● Use separate digital and analog planes. The analog ground plane should be connected
to the digital ground plane via a single point on the PCB.
● Filter power to the analog power planes. It is recommended to connect capacitors, with
good high frequency characteristics, between the power and ground lines,
placing
0.1µF and optionally, if needed 10pF capacitors as close as possible to the ST7 power
supply pins and a 1 to 10µF capacitor close to the power source (see Figure 100).
● The analog and digital power supplies should be connected in a star network. Do not
use a resistor, as V
AREF
is
used as a reference voltage by the A/D converter and
any
resistance would cause a voltage drop and a loss of accuracy.
● Properly place components and route the signal traces on the PCB to shield the analog
inputs. Analog signals paths should run over the analog ground plane and be as short
as possible. Isolate analog signals from digital signals that may switch while the analog
inputs are being sampled by the A/D converter. Do not toggle digital outputs on the
same I/O port as the A/D input being converted.
Figure 100. Power supply filtering
V
SS
V
DD
V
DD
ST72XXX
V
AREF
V
SSA
POWER
SUPPLY
SOURCE
ST7
DIGITAL NOISE
FILTERING
EXTERNAL
NOISE
FILTERING
1 to 10µF
0.1µF
0.1µF
+
- ST72321xx-Auto 1
- Contents 2
- Doc ID 13829 Rev 1 3/243 3
- 4/243 Doc ID 13829 Rev 1 4
- Doc ID 13829 Rev 1 5/243 5
- 6/243 Doc ID 13829 Rev 1 6
- Doc ID 13829 Rev 1 7/243 7
- 8/243 Doc ID 13829 Rev 1 8
- Doc ID 13829 Rev 1 9/243 9
- 10/243 Doc ID 13829 Rev 1 10
- Doc ID 13829 Rev 1 11/243 11
- Doc ID 13829 Rev 1 13/243 13
- 14/243 Doc ID 13829 Rev 1 14
- 16/243 Doc ID 13829 Rev 1 16
- Doc ID 13829 Rev 1 17/243 17
- 1 Description 18
- ST72321xx-Auto Description 19
- 2.1 Package pinout 20
- 2.2 Pin description 22
- 4 Flash program memory 29
- 4.4 ICC interface 30
- Doc ID 13829 Rev 1 31/243 31
- 4.7 Related documentation 32
- 5.1 Introduction 33
- 5.2 Main features 33
- 5.3 CPU registers 33
- 5.3.1 Accumulator (A) 34
- 5.3.3 Program counter (PC) 34
- Interrupt management bits 35
- 36/243 Doc ID 13829 Rev 1 36
- 6.1 Introduction 37
- 6.2 Main features 37
- 6.3 Phase locked loop 38
- 6.4 Multi-oscillator (MO) 38
- Crystal/ceramic oscillators 39
- Internal RC oscillator 39
- 6.5.1 Introduction 40
- 6.5.5 Internal watchdog RESET 42
- Doc ID 13829 Rev 1 43/243 43
- Monitoring the V 44
- main supply 44
- 6.6.3 Low power modes 46
- 6.6.4 Interrupts 46
- SICSR description 47
- Application notes 48
- 7 Interrupts 49
- Servicing pending interrupts 50
- Non-maskable sources 51
- Maskable sources 51
- 52/243 Doc ID 13829 Rev 1 52
- HARDWARE PRIORITY 52
- 7.6 External interrupts 57
- Interrupts ST72321xx-Auto 58
- ST72321xx-Auto Interrupts 59
- 8 Power saving modes 62
- 8.3 Wait mode 63
- 8.4.1 Active Halt mode 65
- 8.4.2 Halt mode 67
- Halt mode recommendations 69
- 9 I/O ports 70
- 9.2.2 Output modes 71
- 9.2.3 Alternate functions 71
- 1. The diode to V 72
- ST72321xx-Auto I/O ports 73
- 9.3 I/O port implementation 74
- 9.4 Low power modes 75
- 9.5 Interrupts 75
- 10 Watchdog timer (WDG) 77
- 78/243 Doc ID 13829 Rev 1 78
- 10.5 Low power modes 80
- 10.8 Interrupts 80
- 10.9 Register description 81
- (MCC/RTC) 82
- Low power modes 83
- Interrupts 83
- 12.2 Functional description 88
- Doc ID 13829 Rev 1 89/243 89
- 90/243 Doc ID 13829 Rev 1 90
- 12.2.8 Input capture function 91
- 92/243 Doc ID 13829 Rev 1 92
- 12.3 ART registers 93
- 13 16-bit timer 98
- 13.3 Functional description 99
- 16-bit timer ST72321xx-Auto 100
- 16-bit read sequence 101
- 13.3.2 External clock 102
- 13.3.3 Input capture 103
- 104/243 Doc ID 13829 Rev 1 104
- 13.3.4 Output compare 105
- 106/243 Doc ID 13829 Rev 1 106
- Doc ID 13829 Rev 1 107/243 107
- 13.3.6 One Pulse mode 108
- Doc ID 13829 Rev 1 109/243 109
- Procedure 110
- 13.4 Low power modes 112
- 13.5 Interrupts 112
- 13.6 Summary of timer modes 112
- 13.7 16-bit timer registers 113
- ST72321xx-Auto 16-bit timer 115
- 117
- Related documentation 120
- 14.1 Introduction 121
- 14.2 Main features 121
- 14.3 General description 121
- 14.3.1 Functional description 122
- 14.3.3 Master mode operation 124
- 14.3.5 Slave mode operation 125
- 126/243 Doc ID 13829 Rev 1 126
- Doc ID 13829 Rev 1 127/243 127
- CPHA = 1 127
- CPHA = 0 127
- 14.5 Error flags 128
- 14.5.4 Single master systems 129
- 14.6 Low power modes 130
- 14.7 Interrupts 130
- 14.8 SPI registers 131
- 15.3 General description 136
- Figure 62. SCI block diagram 137
- 15.4 Functional description 138
- 15.4.2 Transmitter 139
- 15.4.3 Receiver 140
- Doc ID 13829 Rev 1 141/243 141
- 142/243 Doc ID 13829 Rev 1 142
- Extended baud rate generation 143
- Parity control 144
- SCI clock tolerance 144
- Clock deviation causes 145
- Noise error causes 145
- 15.5 Low power modes 146
- 15.6 Interrupts 146
- 15.7 SCI registers 147
- 16.3 General description 156
- 16.3.3 SDA/SCL line control 157
- 16.4 Functional description 158
- 16.4.2 Master mode 159
- Slave address transmission 160
- Master receiver 160
- Master transmitter 160
- Error cases 161
- 16.5 Low power modes 163
- 16.6 Interrupts 163
- 16.7 Register description 164
- 16.7.2 I 165
- C status register 1 (SR1) 165
- 16.7.3 I 167
- C status register 2 (SR2) 167
- 16.7.4 I 168
- 16.7.5 I 169
- C data register (DR) 169
- 16.7.6 I 169
- C own address register (OAR1) 169
- 16.7.7 I 170
- C own address register (OAR2) 170
- Table 90. I 171
- 17.1 Introduction 172
- 17.2 Main features 172
- 17.3 Functional description 173
- 17.4 Low power modes 174
- 17.5 Interrupts 174
- 17.6 ADC registers 174
- 17.6.2 Data register (ADCDRH) 175
- 17.6.3 Data register (ADCDRL) 176
- 18 Instruction set 177
- 18.1.1 Inherent 178
- 18.1.2 Immediate 179
- 18.1.3 Direct 179
- 18.1.5 Indirect (short, long) 180
- 18.2 Instruction groups 181
- 18.2.1 Using a prebyte 182
- 19 Electrical characteristics 185
- 19.3 Operating conditions 188
- IT+(LVD) 189
- : Flash devices 192
- Power consumption vs f 192
- 19.5.1 General timings 195
- 19.5.2 External clock source 195
- 19.5.5 PLL characteristics 198
- 19.6 Memory characteristics 199
- 200/243 Doc ID 13829 Rev 1 200
- 201
- Doc ID 13829 Rev 1 205/243 205
- 206/243 Doc ID 13829 Rev 1 206
- 19.9.1 Asynchronous RESET pin 207
- 208/243 Doc ID 13829 Rev 1 208
- 19.9.2 ICCSEL/V 209
- ICCSEL/V 210
- PROGRAMMING 210
- Doc ID 13829 Rev 1 213/243 213
- 19.11.2 214
- ±5% tolerance 215
- ±2% tolerance 215
- INJ(PIN) 216
- Doc ID 13829 Rev 1 217/243 217
- 218/243 Doc ID 13829 Rev 1 218
- 19.12.3 ADC accuracy 219
- 20 Package characteristics 220
- 21.1.1 Flash configuration 223
- Doc ID 13829 Rev 1 227/243 227
- 230/243 Doc ID 13829 Rev 1 230
- 21.3 Development tools 231
- 21.4 ST7 application notes 233
- 22 Known limitations 234
- Doc ID 13829 Rev 1 235/243 235
- 236/243 Doc ID 13829 Rev 1 236
- Doc ID 13829 Rev 1 237/243 237
- 238/243 Doc ID 13829 Rev 1 238
- 22.1.8 16-bit timer PWM mode 239
- 22.2 All Flash devices 240
- Doc ID 13829 Rev 1 241/243 241
- 23 Revision history 242
Electrolux ENN12901AW podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Nie Electrolux ENN12901AW.
Dostarczamy 1 pdf podręczników Electrolux ENN12901AW do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentarze do niniejszej Instrukcji